Home Page Products Page Service Projects Contact Support


Power Semiconductors

SKiiP®2,3 Integrated intelligent Power Systems [600V] —[1200V]— [1700V]



Summary of standard 600V-SKiiP®2,3
Type Circuit VCES/ V IC/ A5 IRMS1 IRMS2 Options3 Case Interface
SKiiP®2 - standard types with NPT-IGBT and freewheeling CAL-Diode®
202 GD 061-359 CTV 6-pack 600 200 146 104 U,L,W S3 GD
302 GD 061-359 CTV 6-pack 600 300 188 137 U,L,W S3 GD
402 GD 061-358 CTV 6-pack 600 400 2007) 178 U,L,W S3 GD
802 GB 061-259 CTV 2-pack 600 800 4007) 383 U,F,L,W S2 GB
1602 GB 061-459 CTV 2-pack 600 1600 8007) 665 U,F,L,W S4 GB


SKiiP®3 Standard types (preliminary)
Type Circuit VCES/ V IC/ A5 Options3 Case Interface
613 GD 061-3DU 6-pack 600 600 L,W S33 GD
803 GD 061-3DU 6-pack 600 800 L,W S33 GD
Features
  • Low thermal impedance
  • Optimal thermal management with integrated heatsink
  • Pressure contact technology with increased power cycling capability
  • Compact design
  • Low stray inductance
  • High power, small losses
  • Fast and soft recovery CAL diode
  • Recycable
  • Integrated current sensors
  • Integrated driver with
    • Overtemperature protection
    • Overcurrent protection due to current sensors
    • Overvoltage protection (DC-link) (-option-)
    • Built-in dead time and interlock
    • CMOS compatible inputs
    • Fiber optic connector (option for halfbridges)
Typical Applications
  • Half, Fullbridges and H-bridges
  • Three phase motor drive inverter
  • Uninterruptable power supplies UPS
  • Converter
  • General power switching supplies
  • Inductive heating
  • DC Chopper

1. Output rms-phase-current with typical operating conditions as shown in table below, SKiiP 2 mounted on P16 heat sink with standard fan SKF16B-230-01

VCES/V VV/V VD/V cos phi fsw/kHz fout/Hz Tjmax/°C Ta/°C
600 230 320 0.8 5 50 125 40
1200 400 540 0.8 5 50 125 40
1700 690 932 0.8 2 50 125 40

2. Output rms-phase-current with operating conditions as above but 150% overload capability for 60s and fout=2Hz - 50 Hz
3. Available options:
U: DC-link voltage sense and over-voltage protection
F: Fiber optic connector
E: brake chopper voltage levels for 400V mains voltage (for 1200V-SKiiP only)
A: brake chopper voltage levels for 460V mains voltage (for 1200V-SKiiP only)
L: SKiiP®2,3 mounted on P16 (SKiiP®3: PX16 except SKiiP®313GD122-3DUL, SKiiP®413GD061-3DUL) heat sink for air cooling
W: SKiiP 2,3 mounted on NWK40 heat sink for liquid cooling
5. Current per switch @ 25 °C heat sink temperature temperature
6. This type has two gate drivers; when Option "U" is ordered only one gate driver is equipped with Option "U"
7. Maximum continuous current is limited by current sensor capability